Billy-goat FM3301IN Manuel d'utilisateur Page 4
- Page / 20
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Part No. 520188 Form No. F110404B
..
..
Page 4 of 20
5.On each side of the mower, insert
one of the handle mounting bolts
(Item 102) with split lock washer
(Item 6) on top of fl at washer (Item
184) through the hole in one end of
the handle brace (Item 32), the front
handle mounting hole of the handle
and screw into the front handle
mounting hole in the engine base
chassis (Figure 11-5).
6. Assemble blade clutch lever (Item
76) to upper handle using pin (Item
97), washer (Item 150, and pal nut
(Item 3) (see fi gure 11-6 and 11-7).
7.Position control cables and use 2
cable ties on each handle to secure
the cables in position. The top cable
tie should be 1” below the console
and the lower tie should be 12”
below the console (see fi gure 11-8
and 11-9).
8.Check the position of the shift rod
guide (Item 69), and if necessary,
snap it in place in the shift bracket
(Item 78) as shown in Figure 11-8.
9.Put shift lever in NEUTRAL,
depress the brake lever (release
the brake) and carefully pull the
machine back off the pallet.
10.Fill with oil and gas to the proper
level and the unit is ready to mow.
(a battery will also have to be
installed on electric models.)
11.Read the operator’s manual.
11
ASSEMBLY
PUT OIL IN ENGINE BEFORE STARTING.
Read all safety and operating instructions
before assembling or starting this unit.
Your Billy Goat Mower is shipped from the factory
in one crate, completely assembled except for the
handles and console assembly.
DISCONNECT SPARK PLUG WIRE
BEFORE ASSEMBLING UNIT.
1.Cut and remove the nylon
retaining straps (see fi gure
11-1).
2.With the console and handle
assembly positioned as shown
in Figure 11-3, insert the shift
linkage rod (Item 31) into the
shift linkage connector (Item 54).
3. To assemble the shift rod (item
31) to the shift linkage (item 54),
use the roll pin in the parts/
literature bag. If you’ll notice on
the shift linkage, the hole is larger
on one side than the other.
It will be easier to start the roll
pin from the larger side, forcing
it through the shift rod and the
hole on the other side of the shift
linkage, using a hammer or large
adjustable pliers.
4. Insert one of the handle mounting
bolts (Item 102) with split lock washer (Item 6) on top of fl at washer
(Item 184) through the rear handle mounting hole of the right side
handle, and screw it into the rear handle mounting hole on the right
side of engine base chassis (Item 61). Repeat this procedure for the
left side using the left handle.
NOTE: All item numbers called out in the assembly,
operation, and maintenance sections of this manual can
be found on Parts List (pages 15-18).
Figure 11-1
Figure 11-3
Figure 11-4
Figure 11-5
Figure 11-8
Figure 11-9
Figure 11-10
Cable
Ties
117
191
3
122
11
76
97
Figure 11-6 Figure 11-7
Produits connexes et manuels pour Matériel de jardinage Billy-goat FM3301IN
(8 pages)Samsung YP-U4AR podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Nie Samsung YP-U4AR.
Dostarczamy 1 pdf podręczników Samsung YP-U4AR do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commentaires sur ces manuels